"Cooling in Injection Molding: A Three-Dimensional Numerical Simulation," K. Himasekhar, J. Lottey and K. K. Wang, Proc. Supercomputers: Emerging Applications in Manufacturing, 3-1- 3-11 (1989).

"Five-Axis Swept Volumes for Graphic NC Simulation and Verification," K. Sambandan and K. K. Wang, Proc. Design Automation Conference, ASME, Advances in Design Automation - 1989, Vol. 1: Computer-Aided and Computational Design, DE-Vol. 19-1, Ed. B. Ravani, September 1989, pp. 143-150.

"Modelling the Flow and Solidification for Semi-Solid Sn-Pb Alloy," L. S. Turng and K. K. Wang, Paper No. G-T89-043, Trans. 15th International Die Casting Congress, North American Die Casting Association (1989).

"The Basic Research Issues in Computer-Aided Design and Manufacturing Processes," Organization of Engineering Knowledge for Product Modelling in Computer Integrated Manufacturing, Proc. of the Second Toyota Conference, T. Sata (editor), Elsevier Science Publisher, 39-59 (1989).

"Measurement of Thermal Conductivity of Polymer Melts by the Line-Source Method," H. Lobo and C. Cohen, Polymer Engineering and Science, 30, 65-70 (1990).

"The Motion of Rodlike Particles in the Pressure-Driven Flow Between Two Flat Plates," C. A. Stover and C. Cohen, Rheologica Acta, 29, 192-203 (1990).

107. "Automatic Interpretation of Weld Lines and Air Traps in Injection Molding by Synthesizing Deterministic and Heuristic Knowledge," W. R. Jong and K. K. Wang, SPE Technical Papers, 36, 197-202 (1990).

"A Theoretical and Experimental Investigation of Warpage in Injection Molding," N. Santhanam and K. K. Wang, SPE Technical Papers, 36, 270-273 (1990).

"Automatic and Optimal Design of Runner Systems in Injection Molding Based on Flow Simulation," W. R. Jong and K. K. Wang, SPE Technical Papers, 36, 385-389 (1990).

"Melt-Viscosity Modelling and Its Effect Upon Injection-Molding Simulation," C. A. Hieber and K. K. Wang, SPE Technical Papers, 36, 943- 947 (1990).

"Design of a Cooling System in Injection Molding: Use of a CAD Tool," K. Himasekhar, J. Lottey and K. K. Wang, SPE Technical Papers, 36, 1103-1106 (1990).

"A Computer-Aided Cooling-Line Design System for Injection Molds," L. S. Turng and K. K. Wang, Journal of Engineering for Industry, 112, 161-167 (1990).

"CAE for Injection Molding: The State-of-the-Art and Research Trends," K. K. Wang, Automation: Strategies for Manufacturing Growth, Proc. of IA'90 Conference, Singapore, 21-34 (1990).

"Curvature-Continuous Gregory Patch: A Modification of Gregory Patch for Continuity of Curvature," K. Takai and K. K. Wang, Proc. Japan-U.S.A. Symposium on Flexible Automation, Kyoto, Japan, 1205-1211 (1990).

"Concurrent Engineering for the Design & Manufacture of Plastic Parts by Injection Molding," K. K. Wang, Proc. METS'90 (Modern Engineering and Technology Seminar) Vol. VI, Mechanical Engineering Session, Taipei, Taiwan, 1-19 (1990).

"Molding, Polymer Injection," K. K. Wang, International Encyclopedia of Composites, Vol. 3, S. M. Lee (editor), VCH Publishers, New York, 478-489 (1990).

"A Unified Simulation of the Filling and Postfilling Stages in Injection Molding. Part I: Formulation and Part II: Experimental Verification," H. H. Chiang, C. A. Hieber and K. K. Wang, Polymer Engineering and Science, 31, 116-139 (1991).

"Assessment of Shrinkage and Warpage Using an Integrated Analysis of Molding Dynamics," H. H. Chiang, K. Himasekhar, S. Lautenbach, N. Santhanam and K. K.Wang, SPE Technical Papers, 37, 242-246 (1991).

"Injection Molding a Center-Gated Disk: Modelling and Measurements for the Filling and Post-Filling Stages Including Gapwise Shrinkage," C. A. Hieber, P. J. Wang and K. K. Wang, SPE Technical Papers, 37, 259-263 (1991).